Marklin CS1, DSD2010 and TrainController 9 Gold

Forum für den "neuen" Drehscheiben-Dekoder DSD2010
Link zum Projekt: http://www.digital-bahn.de/bau_ds2010/d ... onzept.htm
wuwesso
Beiträge: 605
Registriert: So 22. Apr 2012, 07:46
Wohnort: Meckenbach
Re: Marklin CS1, DSD2010 and TrainController 9 Gold

Beitrag von wuwesso » Do 14. Nov 2019, 20:02

Hello,
The main question however is : what shall I put as feedback in the traincontroller screen for "turntable properties>connection>position control>feedback"???
DSD2010 has a feedback signal RM7 = Done Impuls.
This signal you can use in TC.

The feedback signal RM1 ( Active ) can only use with a Bahnwärter/ signalman!

Regards
Wolf Ulrich
MoBaSbs, TAMS-MC, Märklin-M, MM, TC-Gold, DSD-2010 mit *Anzeigemodul* für Mä-7286

plut
Beiträge: 38
Registriert: Fr 25. Jan 2019, 13:26
Re: Marklin CS1, DSD2010 and TrainController 9 Gold

Beitrag von plut » Do 14. Nov 2019, 20:50

Yes but where I find it?

How do I say to traincontroller where rto find it?

In traincontroller I have to specify a feedback for position control in turntable properties, what should I write there?

Thanks for your patience
Andrea

wuwesso
Beiträge: 605
Registriert: So 22. Apr 2012, 07:46
Wohnort: Meckenbach
Re: Marklin CS1, DSD2010 and TrainController 9 Gold

Beitrag von wuwesso » Do 14. Nov 2019, 21:43

Hello,
the RM7 is in the S88-Bus integrated.
You must integrate the S88-Modul of Platine-Ground in your s88-System of CS1.
In TC you must create contact detector with adress: ( s88 Module Adress-Nr ) / Input: 7

If you connect DSD-2010 S88 to S88-Input of CS1 at first position and DIP-Switch is set to "Two Bytes"
the contact detector adress: 1 / Input 7 and you named it "DSD2010-Done"
in the Entryfield position control / turntable properties You Search in the List this Name and after doubleclick the name is in the entryfield.


Sorry I don't know nothing about your Feedback system and the integration of this in TC.
So I can give no better help.
Regards
Wolf Ulrich
MoBaSbs, TAMS-MC, Märklin-M, MM, TC-Gold, DSD-2010 mit *Anzeigemodul* für Mä-7286

plut
Beiträge: 38
Registriert: Fr 25. Jan 2019, 13:26
Re: Marklin CS1, DSD2010 and TrainController 9 Gold

Beitrag von plut » Do 14. Nov 2019, 21:46

Thanks for all Wolf
Andrea

wuwesso
Beiträge: 605
Registriert: So 22. Apr 2012, 07:46
Wohnort: Meckenbach
Re: Marklin CS1, DSD2010 and TrainController 9 Gold

Beitrag von wuwesso » Do 14. Nov 2019, 21:53

Hello,
here some screenshoots
Regards
Wolf Ulrich
Dateianhänge
New contact detector
New contact detector
MoBaSbs, TAMS-MC, Märklin-M, MM, TC-Gold, DSD-2010 mit *Anzeigemodul* für Mä-7286

wuwesso
Beiträge: 605
Registriert: So 22. Apr 2012, 07:46
Wohnort: Meckenbach
Re: Marklin CS1, DSD2010 and TrainController 9 Gold

Beitrag von wuwesso » Do 14. Nov 2019, 21:54

RM-Done.JPG
RM_DONE2.JPG
TC-Done.JPG
MoBaSbs, TAMS-MC, Märklin-M, MM, TC-Gold, DSD-2010 mit *Anzeigemodul* für Mä-7286

wuwesso
Beiträge: 605
Registriert: So 22. Apr 2012, 07:46
Wohnort: Meckenbach
Re: Marklin CS1, DSD2010 and TrainController 9 Gold

Beitrag von wuwesso » Do 14. Nov 2019, 22:11

Hello,
did you clean the motor?
the difference between current left and current right is to much and the current of 20mA is to low.
Regards
Wolf Ulrich
MoBaSbs, TAMS-MC, Märklin-M, MM, TC-Gold, DSD-2010 mit *Anzeigemodul* für Mä-7286

wuwesso
Beiträge: 605
Registriert: So 22. Apr 2012, 07:46
Wohnort: Meckenbach
Re: Marklin CS1, DSD2010 and TrainController 9 Gold

Beitrag von wuwesso » Fr 15. Nov 2019, 21:06

Hello,
Sound is not working at all.
- Loudspeaker 8Ohms and soundbody correct connected to susi modul?
- turntable sound loaded on susi modul?
- with Ohmmeter check if there is less than 8Ohm at lautspeacker cable

Warning:
Volume is set to 255 this is maximum.
No good idea, because loudspeaker can be damaged on turning system on.
Regards
MoBaSbs, TAMS-MC, Märklin-M, MM, TC-Gold, DSD-2010 mit *Anzeigemodul* für Mä-7286

plut
Beiträge: 38
Registriert: Fr 25. Jan 2019, 13:26
Re: Marklin CS1, DSD2010 and TrainController 9 Gold

Beitrag von plut » Fr 22. Nov 2019, 12:03

7,3 Ohm at loudspeaker, less than 8.

No sound

Thanks

plut
Beiträge: 38
Registriert: Fr 25. Jan 2019, 13:26
Re: Marklin CS1, DSD2010 and TrainController 9 Gold

Beitrag von plut » Fr 22. Nov 2019, 16:44

The sound does not work but also the blinking led has never worked.
Maybe the two things are due to the same problem? (the BÜHNE ?)

The house led works well, with TC 9 and with CS1 alone.

Thanks for any help
Andrea


Antworten